Author Topic: Bulkhead Cover Plates  (Read 749 times)

Online Willie_B

  • CREW
  • 1275cc
  • *****
  • Posts: 925
  • Total likes: 48
  • Karma: 7
  • He who laughs last, thinks slowest.
    • Lilburn, GA,
Re: Bulkhead Cover Plates
« Reply #25 on: July 29, 2019, 11:14:02 AM »
Nice cover - Offering some really high quality parts

 Apparently online store is coming.
    My buddy Cole has some ' Non Serviceable sealed Mini specific ball joints on the way from David...  (not metro) but same concept.

Thoughtful upgrade to not mess with ball joint tension anymore...

I saw those too. They look like a real PITA time saver. I hope Cole does a review of them.

Offline MiniDave

Re: Bulkhead Cover Plates
« Reply #26 on: July 29, 2019, 11:30:17 AM »
How much were those? I agree, not having to shim them would be great!
1989 Cooper Racing Green
2009 Clubman S
2004 Audi Allroad 2.7 TT

Offline jedduh01

Re: Bulkhead Cover Plates
« Reply #27 on: July 29, 2019, 01:15:24 PM »

50$ per Ball joint...  200$ For a set.


At first # i thought that was High.. But then i had to Install a ball joint in my Volvo XC90 == 45$ for the part from MOOG  at Advance auto... then it was a Slam it out slam it in affair all in about 45 Min... No problem.

    This conversion for the mini could be really practical and time saving and modern upgrade.


Cole will have a review , Cole needs to keep his car on the road to put some MILES on it, but will be installed hopefully this week.
« Last Edit: July 29, 2019, 01:23:40 PM by jedduh01 »

Offline MiniDave

Re: Bulkhead Cover Plates
« Reply #28 on: July 29, 2019, 01:28:41 PM »
Yikes! $200 a set, plus shipping is pretty stiff.....If I were working in a shop and spending OPM, I would def do them.
1989 Cooper Racing Green
2009 Clubman S
2004 Audi Allroad 2.7 TT

Offline Jimini II

Re: Bulkhead Cover Plates
« Reply #29 on: July 30, 2019, 09:53:55 PM »
Yikes! $200 a set, plus shipping is pretty stiff.....If I were working in a shop and spending OPM, I would def do them.

I think if you were paying a mechanic to install and set up new ball joints it would be cheaper at $200 plus the minimal labor to fit these when compared to the labor time on the old style ones imo.
Then there is the plus factor of never having to adjust them again.

Offline BruceK

Re: Bulkhead Cover Plates
« Reply #30 on: July 31, 2019, 07:59:21 AM »
Plus not having to grease them too!
1988 Austin Mini
2002 MINI Cooper S
2007 Triumph Bonneville

Offline MPlayle

Re: Bulkhead Cover Plates
« Reply #31 on: July 31, 2019, 09:27:42 AM »
Plus not having to grease them too!

That was going to be one of my questions: whether they required greasing like the originals.

Offline Jimini II

Re: Bulkhead Cover Plates
« Reply #32 on: August 01, 2019, 03:03:55 PM »
No they are sealed for life much like the early Metro hubs.

Offline MiniDave

Re: Bulkhead Cover Plates
« Reply #33 on: August 01, 2019, 06:30:14 PM »
While I had the main harness out I went ahead and fit the bulkhead cover - it's pretty simple. First I installed the foam seal in the machined groove on the back. Then I screwed the two halves together and put it up on the bulkhead so I could mark the holes. Once I drilled the holes I trial fit it and it fits perfectly. I think it looks great and it's bound to make things quieter compared to just having the hole open to the engine and carbs.
1989 Cooper Racing Green
2009 Clubman S
2004 Audi Allroad 2.7 TT

Offline tmsmini

Re: Bulkhead Cover Plates
« Reply #34 on: August 01, 2019, 08:19:51 PM »
On earlier cars will it used the exiting machine screw holes that hold the pod in place?

Offline MiniDave

Re: Bulkhead Cover Plates
« Reply #35 on: August 01, 2019, 08:52:20 PM »
Good question.....I don't think so but I don't really know. My other car is even newer than this one....
1989 Cooper Racing Green
2009 Clubman S
2004 Audi Allroad 2.7 TT

Offline Jimini II

Re: Bulkhead Cover Plates
« Reply #36 on: August 02, 2019, 07:47:12 AM »
On earlier cars will it used the exiting machine screw holes that hold the pod in place?

I don't think they will. If you look at the part the tab on the top right is not symmetrical with the others, from memory the early cars are evenly spaced.

Offline MiniDave

Re: Bulkhead Cover Plates
« Reply #37 on: August 02, 2019, 11:08:03 AM »
I think you're right, I think they are where the larger holes are around the plate on my car. On an Inno those holes are used to secure the middle of the dash - it has a metal brace that is attached with screws thru those holes.
1989 Cooper Racing Green
2009 Clubman S
2004 Audi Allroad 2.7 TT

Offline TRP

  • Active members
  • *
  • Posts: 2
  • Total likes: 0
  • Karma: 0
    • Morgan Hill, California
Re: Bulkhead Cover Plates
« Reply #38 on: August 12, 2019, 02:19:01 PM »
I would love one of these but I don't use Facebook. Is there any other way to order these lovely bulkhead plates?

Ted

Offline MiniDave

Re: Bulkhead Cover Plates
« Reply #39 on: August 12, 2019, 02:41:08 PM »
Hey Ted, how you pay for stuff online? Do you use paypal or credit cards or what? Let me email him and see if he'll give me an email address to order direct thru.

Or, if you use Paypal, you can send me $100 and I'll order one for you - send me your address and so on so you only pay shipping once. Alternately you can also just mail me a check if you prefer.....PM your info to me and I'll do the same.

Edit: I sent the guy in Japan a note to ask for his email address, but due to the time difference I may not hear from him till tomorrow.
« Last Edit: August 12, 2019, 03:00:46 PM by MiniDave »
1989 Cooper Racing Green
2009 Clubman S
2004 Audi Allroad 2.7 TT

Offline TRP

  • Active members
  • *
  • Posts: 2
  • Total likes: 0
  • Karma: 0
    • Morgan Hill, California
Re: Bulkhead Cover Plates
« Reply #40 on: August 12, 2019, 07:35:49 PM »
I use paypal/venmo/bitcoin etc.

I'll reach out to David.

Thank you!
Ted